How To 911/912: Front Suspension Pan Restoration

by

If you’re interested in restoring a vintage Porsche 911 or 912, this is a great starting point.

In this step-by-step video, we’ll show you how to restore your front suspension pan.

First off, you’ll have to remove all of the rusted metal. For our own restoration, this took about 8 hours.

Depending on where your Porsche is cut, you can trim our front suspension pan piece to fit your specifications. It’s also a good idea to spray it with weld-through primer.

Once you’ve done this, you can begin securing it with self-tapping screws to the body of your vintage Porsche.

If you think you’ve got it in the right place, you can test it out by lining it up with your suspension. From there you can adjust it to fit if you need to.

Check out our video for more details about this step in the restoration process!

 

Restoration Design’s Porsche 911ST: Introduction

by

In 2013, we decided to restore a 1972 911ST – our first!

The project started off the same way most restoration projects do: we sanded the body down and realized there was more rust damage than we had anticipated.

The sanding also revealed that the 911 had been in a front-end collision, meaning we had to replace the entire inner fender.

This model of Porsche didn’t come with proper ending panels and didn’t have rock guard, so we would be doing the same with this restoration.

The ST we purchased was produced for racing. While American race cars were building bigger engines to win races, Porsche increased their horsepower and made their cars more nimble and a lot lighter – which proved to be successful.

These models also didn’t come with ashtrays, glove boxes, the heating and ductwork was removed and the gas tank fill was located under the hood.

Check out the video to see the ST before we restored it, and check out our other videos to see the restoration process!

Restoration Spotlight: Making of the Porsche 356A Hood

by

Back in the fall of 2007, we noticed a substantial need for hoods for 356s. Getting a good quality hood was pricey and often difficult. So, we decided to start making them ourselves.

To start, we purchased one of these good quality hoods from the US. Painting it matte black and getting some of the minor imperfections out made it possible for us to use this as a template for scanning.

We got the scanning done by a third-party, who then sent us the scan. We imported the scan into our own computer system so we could design the dye. Designing each dye typically takes 100-200 hours – just for design time.

After the dye was designed, we had to design the different tool paths for 4-6 different tools.

From there, we had to machine the dye using steel and composite to withstand the pressure of the press.

After the dye is machined, it needs to be polished. Polishing the male and female parts of the dye for the 356 hood took about 16 weeks in total.

Check out the video to see the rest of the process and the finished product!

Build Your Own DIY-Rotisserie: Porsche 914

by

Embarking on your very own Porsche 914 restoration? Our DIY rotisserie makes it easy.

By cutting all the proper lengths of 1 1/4” square tubing with proper angles, you can build this rotisserie to perfectly fit your 914.

Make sure you are measuring properly, and laying out the tubing to ensure you have all the proper lengths and angles before you weld them together.

We also use caster wheels – a 4” caster wheel is sufficient for home shops.

Building your own rotisserie around your 914 allows you to roll the car over easily, with the help of another person, so you can reach the underside and other angles of your car.

This same rotisserie can also be adjusted to fit a 356 or 911, depending on your restoration project.

Check out the video for specific instructions to build your rotisserie!

Restoration Spotlight: 1967 Porsche 911 “The Pink Pig”

by

If you’ve ever seen us at a major Porsche meet in the US or Canada, you’ve probably seen our 911, the Pink Pig.

The Pink Pig is the nickname of our 1967 Porsche 911 which we originally bought in the US for $800. While we initially bought it to sell it for panels, we soon identified a better use for it.

We use the Pink Pig for showing people how and where different parts that we make fit onto a restoration.

We outline parts with red lines and mark the part number on the car.

But why the pink? The unique colour is to mimic the 917 Porsche race car. It’s thought that the race car was painted overnight by its mechanics, and it had red lines on it to distinguish meat cuts.

Check out the video to see the Pink Pig!

Post Navigation

 
Newer Posts →